f87818ea tuexen Jan. 3, 2022, 10:03 p.m.
4ccd6c13 alc Jan. 3, 2022, 7:14 p.m.
A feature of arm64's instruction for TLB invalidation is the ability
to determine whether cached intermediate entries, i.e., L{0,1,2}_TABLE
entries, are invalidated in addition to the final entry, e.g., an
L3_PAGE entry.

Update pmap_invalidate_{page,range}() to support both types of
invalidation, allowing the caller to determine which type of
invalidation is performed.

Update the callers to request the appropriate type of invalidation.

Eliminate redundant TLB invalidations in pmap_abort_ptp() and
pmap_remove_l3_range().

Add a comment to pmap_invalidate_all() making clear that it always
invalidates entries at all levels.

As expected, these changes result in a tiny yet measurable
performance improvement.

Reviewed by:	kib, markj
MFC after:	3 weeks
Differential Revision:	https://reviews.freebsd.org/D33705
cgit
afad340a glebius Jan. 3, 2022, 6:20 p.m.
Reviewed by:		tuexen
Differential revision:	https://reviews.freebsd.org/D33543
cgit
fec8a8c7 glebius Jan. 3, 2022, 6:17 p.m.
Provide structure inpcbstorage, that holds zones and lock names for
a protocol.  Initialize it with global protocol init using macro
INPCBSTORAGE_DEFINE().  Then, at VNET protocol init supply it as
the main argument to the in_pcbinfo_init().  Each VNET pcbinfo uses
its private hash, but they all use same zone to allocate and SMR
section to synchronize.

Note: there is kern.ipc.maxsockets sysctl, which controls UMA limit
on the socket zone, which was always global.  Historically same
maxsockets value is applied also to every PCB zone.  Important fact:
you can't create a pcb without a socket!  A pcb may outlive its socket,
however.  Given that there are multiple protocols, and only one socket
zone, the per pcb zone limits seem to have little value.  Under very
special conditions it may trigger a little bit earlier than socket zone
limit, but in most setups the socket zone limit will be triggered
earlier.  When VIMAGE was added to the kernel PCB zones became per-VNET.
This magnified existing disbalance further: now we have multiple pcb
zones in multiple vnets limited to maxsockets, but every pcb requires a
socket allocated from the global zone also limited by maxsockets.
IMHO, this per pcb zone limit doesn't bring any value, so this patch
drops it.  If anybody explains value of this limit, it can be restored
very easy - just 2 lines change to in_pcbstorage_init().

Differential revision:	https://reviews.freebsd.org/D33542
cgit
644ca084 glebius Jan. 3, 2022, 6:15 p.m.
Now that each module handles its global and VNET initialization
itself, there is no VNET related stuff left to do in domain_init().

Differential revision:	https://reviews.freebsd.org/D33541
cgit
24e1c6ae glebius Jan. 3, 2022, 6:15 p.m.
There left only three modules that used dom_init().  And netipsec
was the last one to use dom_destroy().

Differential revision:	https://reviews.freebsd.org/D33540
cgit
9880323a glebius Jan. 3, 2022, 6:15 p.m.
While here, use just static initializer for key_cb.

Differential revision:	https://reviews.freebsd.org/D33539
cgit
340c7343 glebius Jan. 3, 2022, 6:15 p.m.
The function now modifies pr_usrreqs only, which are always
global.  Rename it to pr_usrreqs_init().

Differential revision:	https://reviews.freebsd.org/D33538
cgit
89128ff3 glebius Jan. 3, 2022, 6:15 p.m.
The historical BSD network stack loop that rolls over domains and
over protocols has no advantages over more modern SYSINIT(9).
While doing the sweep, split global and per-VNET initializers.

Getting rid of pr_init allows to achieve several things:
o Get rid of ifdef's that protect against double foo_init() when
  both INET and INET6 are compiled in.
o Isolate initializers statically to the module they init.
o Makes code easier to understand and maintain.

Reviewed by:		melifaro
Differential revision:	https://reviews.freebsd.org/D33537
cgit
321e586e markj Jan. 3, 2022, 6 p.m.
largepage_mprotect maps a superpage and later extends the mapping.  This
occasionally fails with ASLR disabled.  To fix this, first try to
reserve a sufficiently large virtual address region.

Reported by:	Jenkins
MFC after:	1 week
Sponsored by:	The FreeBSD Foundation
cgit
0e494a9e markj Jan. 3, 2022, 6 p.m.
Some AMD Geode-based systems end up using the 8254 PIT to calibrate the
TSC during late calibration, which doesn't work because that
timecounter's mask (65535) is much smaller than its frequency (1193182).
Moreover, early calibration is done against the 8254 timer anyway.

Work around the problem by simply using early calibration results if no
high-quality timecounters exist.

PR:		260868
Fixes:		22875f88799e ("x86: Implement deferred TSC calibration")
Reported and tested by:	mike@sentex.net, Stefan Hegnauer <stefan.hegnauer@gmx.ch>
Reviewed by:	imp, kib
MFC after:	3 days
Sponsored by:	The FreeBSD Foundation
Differential Revision:	https://reviews.freebsd.org/D33730
cgit
5ba41925 markj Jan. 3, 2022, 6 p.m.
The PREEMPTION option is enabled in all GENERIC kernel configurations.

MFC after:	1 week
cgit
80871aeb kp Jan. 3, 2022, 5:35 p.m.
Pointed out by:	imp
Sponsored by:	Rubicon Communications, LLC ("Netgate")
cgit
3582b9e3 jrtc27 Jan. 3, 2022, 5:09 p.m.
Currently, any errors when adding a PIC child handler are ignored,
instead just continuing on to registering that PIC as an MSI, and
ignoring any errors that occur for that too.

Reviewed by:	andrew
MFC after:	1 week
Differential Revision:	https://reviews.freebsd.org/D33342
cgit
a3e828c9 jrtc27 Jan. 3, 2022, 5:08 p.m.
Currently intr_pic_add_handler either returns the PIC you gave it (which
is useless and risks causing confusion about whether it's creating
another PIC) or, on error, NULL. Instead, convert it to return an int
error code as one would expect.

Note that the only consumer of this API, arm64's gicv3_its, does not use
the return value, so no uses need updating to work with the revised API.

Reviewed by:	markj, mmel
MFC after:	1 week
Differential Revision:	https://reviews.freebsd.org/D33341
cgit